Відео

Very helpful. Thanks a lot!

Hey there I hope some can see this. I need help and don’t know what to do. I made the rows but cannot select individual boxes. Yes I’m clicking on the arrow, but every time I try to select a box it either doesn’t select her it select the whole row. Please help

You mentioned consistency a couple of times - as a newbie I'm not sure what consistency my paint should be at to be good for this airbrush. Should it be like milk? Would that be the best way to describe it? Thanks for the video!

That's a pretty nice design. I like how it uses magnets. You can use them anywhere that a magnet could go. I can see it being used in places or situations like if you were working on a car or a welding table or whatever. You are not limited to just using it with that plate on a tabletop. It's more versatile than normal helping hands.

Phil Nolan, Subscribed because your videos are always awesome!

Hovsco Porto Max Electric Scooter ($50 off: MTV): www.hovsco.com/PhilNolan

Is there a waz how to upload this printer to Prusa Slicer? Anything I have tried failed miserably...

For 'convenience' burn the tests of each material on a sheet of the same size as each other (3x5, 6x8, 8x11, etc) and cut three holes on the left to fit them all into a 3 ring binder. can glue paper on the back for your notes. (OR burn them in with the laser, lol)

exellent video, i hace one question. to print in 500 mm/sec, what temp is set on your nozzel? cause, i put in 150 mm/s in polyterra and 195 celsius and i had underextrusions in some parts.

Hovsco Porto Max Electric Scooter ($50 off: MTV): www.hovsco.com/PhilNolan

You should always wipe any parts down to remove sand paper debris and powdered filament otherwise you will not get the strongest bond. Usually rubbing alcohol will also remove most oils and debris well and leave a good bonding surface. For the strongest bond with any adhesive PREP the surface leave it clean.

Lost me at Glue

I don't have the "apply mask to image" option any ideas?

go check out faux hammer bit on this one. this printer is pos.. it has so many flaws and issues. and its not 14k.. check the specs on the screen and see :) this is no buy folks.

Wow too big. Thanks for sharing your findings on this one.

Does look really cool does it work in resin

A tip for you, I use a Tevo Tornado with a0 6mm with .75mm walls or 0.8mm with 1mm 1mm walls. It reaaaaally improves the strength and still looks good at a .45

Thanks interesting to watch.

Looks really good thanks and I am ready to start learning this. Laurie. NZ.

Hovsco Porto Max Electric Scooter ($50 off: MTV): www.hovsco.com/PhilNolan

This is the best one how can I get it

Ur hands are so shaken i felt like i was going to have a panic attack lol

I always do it wrong 😂 I make points in both component 1&2 on the same places, and that results in mesh will be duplicated some where weirdly... So only shit loads with points in one component and then allign again

I think you were predicting the future when you made this video :-) The new version can make 3 Hueforges at once (no gluing) if you pre-process by shifting the color bands to R, G, B.

Toothbrush and water color sprinkle

does not work for me with differnt pieces and contexte do i forget something? (turntable + lumix s5 in jpeg flat + 50mm at f11 + iso 4000 + sweet daylight exterior & spot light + target + white background + 5 control point + align + normal model ) The components does not merging OR merging but i juste have 2 pieces in one not aligned.

Hi Phil, did you use any sort of glue in the bed? and did you have smooth or rough texture in your bed? I wish to print in tpu antibacterial and i never have printed tpu before. Can you confirm if tpu antibacterial is the same as 95A? i checked its values od density and stuff and theoretically it is the same. I have the same printer and the bed information it would be really appreciated to keep learning about this wonderfull hobby. Thank you so much for your content!:)

Q: What's being used these days to generate the stylized picture used in this tutorial?

You have try to use soften shore TPU or only 95 shore TPU?

can i measure the rock roughness using mesh lab?

Did you have a hard time with anything solid and did you have to make the supports hollow?

Hey Phil, did you have any problems with extrusion? I've heard that TPU can get all tangled up in the direct drive gears of Ender 3 V3 KE.

looks crap

Good job brother!

Nice review! regards from Bolivia

which nozzle did you use the standard one?

Great video Phil! I was struggling with this for a few days until I found your tutorial. I'm a subscriber now.

Hello. Is the power of a mobile phone used to scan on the street? If so, how powerful does the device need to be?

Thank you! How about to combine resione F69 resin with Siraya Tech Tenacious clear for more liquid ? Any Experience?

documents

what the print temp use for the 50mm/s pls ?

I am making a grid as the one in this video but once I have drawn the frame a made my 1st line of squares in the grid I cannot select the 1st square, The select function wont work. It works fine for all the squares selected together but not the single square. Any suggestions. Thanks

I really think gluing is not the way to go I'm sorry but it looks awful

Nice video and great explanation for getting started. Thank you.

Happy birthday, Phil! Also, nice work on the Transformer!

Im found a couple on thingiverse ive printed, so cool! Im purchasing the program tonight. Thanks for the update on the method bq it is. Ill probably have sone questions like how to make them thicker so there not so flimsy!? Thank you this was very helpful!

What temperature settings did you use? Mine keeps stringing and warping no matter what temperature combination I use, and I can't figure out why.

First time watching one of your videos. I see you have a really nice looking background. And then there is a bench that is chucked full of crap next to where you are working. Again I have not seen any of your other videos but this kinda puts me off as it appears your trying to be professional. Also your bench its self is looking pretty bad with all kinds of stains. I understand if you don't have any space to set up both a work bench and a place to film. Maybe cover it with some contact paper that will be easily changed when it starts to get bad.

that's really impressive results!! we just got into making lithophanes

Hello, what is the material of this scanner ? is it plastic?